water injector
英 [ˈwɔːtə(r) ɪnˈdʒɛktə]
美 [ˈwɔːtər ɪnˈdʒɛktər]
喷水装置
双语例句
- Such additives generally have good lubrication, cleaning, in addition to water, rust and other functions, on the injector, fuel pump, engine has great benefits.
一般这类添加剂具有良好的润滑、清洁、除水、除锈等功能，对喷油器、喷油泵、发动机都有很大好处。 - The water injecting hole of the water injector is exposed above floor surface, so the installation and the maintenance are both very convenient.
在安装时，让注水器的注水口露出地面，这样，安装和维修都十分方便。 - Water feed is by rear truck mounted axle pump, injector or Wier pump.
水饲料安装轴泵，喷油器或威尔泵的后方卡车。 - A perforated nozzle for spraying water from a hose or sprinkling can. Study on the Fuel Injection Rate of a Multi-hole Injector Applied to a Direct Injection Gasoline Engine
莲蓬式喷嘴一种使水从管子或喷水壶里喷洒出来的有孔的喷嘴直喷汽油机多孔喷油器的喷油规律研究 - Water is fed into the boiler by a hand pump and an injector.
水靠著手动帮浦和注水器被注入锅炉。 - The water closet is characterized in that a water injector with an upward water injecting hole is arranged on the back end of the closet bowl.
本大便器的特点是，在便盆的后端设一注水口向上的注水器。 - Application of Abrasive Suspension Water Jet on Step-hole of Fuel Injector Deburring
磨料浆体射流去毛刺技术在喷油器体台阶孔上的应用 - Experimental research on Lifting-Pressure and heating process of supersonic steam-water two-phase flow injector in low inlet steam pressure
低进汽压力下超音速两相流升压特性实验研究 - With water as the simulating media, parameters of swirl injector with different spout length such as mass flow rate, sheet cone angle and axial velocity of liquid film were measured on the condition of different pressure difference by the high speed dynamic measuring system.
采用高速动态测量分析系统，以水为模拟介质，对离心喷嘴流量、液膜展开角、喷雾场轴向速度等参数在不同压降工况下，随喷口长度的变化进行了试验研究。 - It is discussed that a method of testing layered water absorbing capacity of water injector by flowmeter directly based on the problems in testing input profile by radioisotope.
该文针对放射性同位素测吸水剖面存在的问题，探讨了用流量计直接测试注水井层段吸水量的方法。 - It is necessary to study the reservoir heterogeneity quantitatively in order to make sure the reservoir connectivity between the water injector and producer.
为了搞清注采层之间的对应性和连通关系，有必要对该区储层非均质性进行定量研究。 - A New Way to Remove Plugging on String Inner Wall in Perforation Interval in Water Injector
注水井射孔段套管内壁堵塞解堵的一种方法 - Study and Application of the Moving Water Injector Well-Flushing Technique in Water Area
注水井活动洗井技术在水网地区的研究与应用 - Depth profile control in water injector is not only an important technology of secondary oil recovery, but also the technical key of tertiary oil recovery in severe heterogeneous oil reservoirs. Depth profile control technology of pre?
注水井深度调剖不仅是一项重要的二次采油技术，而且是严重非均质油藏进行三次采油的技术关键。 - Geologic characteristics of complicated fault-block oil reservoir in Wenzhong area are introduced. Application and effect of some technologies of double target directional well, sidetracking, updating water injector, well pattern recombination, adjusting displacement by profile control of water injection wells are discussed.
介绍了文中复杂断块油藏的地质特征，论述了双靶定向井、侧钻井、注水井更新、井冈重组、注水井调驱等工艺在文中油田的应用及效果。 - Reliability analysis of hot water heating system using water injector to supply water and increase pressure
应用水射器补水加压的热水供暖系统可靠性分析 - Development and application of downhole electric heating technology on water injector in high pour point oilfield
高凝油油田注水井井下电加热技术研制及应用 - The results of circulated heating of the deaeration heating systems were com-pared by using steam injector to replace the hot water circulation pump. It is found that the application of steam injector can enable the effects of save energy, ensure safety, high efficiency and convenience.
将使用蒸汽喷射器替代热水循环泵对除氧加热系统进行循环加热的效果进行了对比，认为应用蒸汽喷射器可以起到节能、安全、高效、方便的作用。 - Crosslinked gel particles is that polymer crosslinked system formed gel by crosslinking at ground, then gel particles have prepared through the processes of granulation, drying, flouring, screening and so on, at last depth profile control in water injector is carried out.
预交联凝胶微粒深度调剖技术是将聚合物交联体系在地面交联形成凝胶，然后经造粒、烘干、粉碎、筛分等工艺过程制备成凝胶微粒，进行注水井深度调剖。 - With the consideration of the problems existed in Daqing Oil Field, such as isotopic contamination during isotopic water injection profile logging, high permeability streaks in formation, injection profile testing for polymer injector, et al., many characteristic production logging techniques have been developed.
针对大庆油田现场存在的同位素吸水剖面测井同位素沾污、地层大孔道、注聚井注入剖面测试等问题，本着实用、配套的原则，重点发展了多项特色生产测井技术。 - Extending new chemical profile control technology of water injector started up 81 layers ( 170m), and increased oil production of corresponding well by 2.04t/d average low-productivity.
推广注水井化学调剖新工艺，启动低产层170m/81层，调剖对应井平均增油2.04t/d； - Oil well downhole abrasive jet slotting technology is a highly new technology for oil well production increasing, injection increasing of water injector and improving oilfield recovery which has been used in Daqing Oilfield, Shengli Oilfield and Liaohe Oilfield, etc. with very good results.
井下磨料射流割缝技术是一项油井增产、水井增注、提高原油采收率的高新技术。已在大庆、胜利、辽河等油田推广使用，效果良好。